Snow White 5ml

Density: low

Colour: chalk white

Contents: Jars of 5ml, 15 ml.

Techniques : Nail reconstruction, Perfect for painting French on the surface without creating thickness, perfect for Nail Art for gel painting techniques, ideal for creating super thin lines.

FEATURES:

• Maximum adherence
• It doesn’t turn yellow
• Flexible 
• Very resistant
• Catalyses perfectly 
• Maleable 
• Pinching 
• Very pigmented
• Opaque
• Stable
• Doesn’t drip

How to use: 

French manicure with the semipermanent nail polish:

1. Sanitize the client's nails with Sanitizer;
2. Opacify the natural nail with the Buffer or with the file Zebra 150/180;
3. Remove excess dust with the nail brush;
4. Evenly clean the entire surface of the nail using a square of pressed cotton soaked in Nail Fresh Nail Prep;
5. Wait a few seconds (about 30 seconds will be enough) for the product to evaporate completely;
6. Apply 1-2 small drops of primer acid being careful not to touch the skin, air dry in seconds. Apply on the nail plate to avoid the cuticle area;
7. Apply a thin layer of Base coat;
8. Cure in UV for 120 sec., In UV / LED 60 sec;
9. Apply a semi-permanent nude nail polish, in pink or beige tones;
10. Cure in UV for 120 sec., In UV / LED 60 sec;
11. With a thin brush, delimit the distal area and then apply the semi-permanent white inside that margin to create the famous moon;
12. Cure in UV for 120 sec., In UV / LED 60 sec;
13. Seal by applying the final polishing Top Coat; 
14. Cure in UV for 120 sec., In UV / LED 60 sec;
15. Remove the dispersion on the surface of the nail with the Cleanser. 

French manicure with gel:

1. Sanitize the client's nails with Sanitizer;
2. Opacify the natural nail with the Buffer or with the file Zebra 150/180;
3. Remove excess dust with the nail brush;
4. Evenly clean the entire surface of the nail using a square of pressed cotton soaked in Nail Fresh Nail Prep;
5. Wait a few seconds (about 30 seconds will be enough) for the product to evaporate completely;
6. Apply 1-2 small drops of primer acid being careful not to touch the skin, air dry in seconds. Apply on the nail plate to avoid the cuticle area;
7. Apply a thin layer of Base coat;
8. Cure in UV for 120 sec., In UV / LED 60 sec;
9. Use the gel brush to apply the builder gel. Proceed with the application of the modeling gel, the densest one, with which you define the shape of the gel nails;
10. Create a perfect curve with the help of the brush. At this stage you need to create a perfect C curve also paying close attention to covering the stress points. At this point the nail must have a thicker area like a slight hill in correspondence of the center of the nail. Warning! It is very important to always keep the gel away from the cuticles and the skin surrounding the nail, never get to touch them to avoid lifting and detachment of the reconstruction;
11. Cure in UV for 120 sec., In UV / LED 60 sec;
12. File the nail with the file Zebra 150/180 file to obtain the length and camber desired
13. Opacify the natural nail with the Buffer or with the file Zebra 150/180;
14. Remove excess dust with the nail brush;
15. Degrease the nails with Cleanser;
16. Apply the coloured gel - light pink or beige - on the whole nail with the exception of the distal margin (the highest part of the nail, so to speak, the one to which we will reserve the white bezel);
17. Cure in UV for 120 sec., In UV / LED 60 sec;
18. Use a nail art brush to delimit the distal margin area and apply then the white gel within this line, creating your white bezel or smile;
19. Take the white gel in small quantities from its container and start, nail by nail, to create the typical French classic bezel. Spread a thin layer of white or coloured gel. It is recommended to make one finger each and cure for a few seconds without degreasing. Choose the technique you prefer most, with the use of the brush. Proceed with caution and without haste and, alternating between the two hands, put each finger in the lamp, until all the nails have dried at perfection;
20. Seal by applying the final polishing Top Coat; 
21. Cure in UV for 120 sec., In UV / LED 60 sec;
22. Remove the dispersion on the surface of the nail with the Cleanser. 

NOTE:

• Suitable for application with ANTARTYC brushes
• Suitable for application on Nail Form